Articles

RWA density formula: how to calculate it, worked case

One ratio says how much regulatory risk sits on each dollar of a bank's balance sheet, and turns a capital requirement into equity per dollar of assets.

RWA density is total risk-weighted assets divided by total assets. It shows how much regulatory risk a bank carries per dollar of balance sheet, and it turns a capital ratio into capital per dollar of assets. On two illustrative banks with $50,000 million of assets each, a mortgage-led lender has $20,600 million of RWA, a density of 41.2%, and a corporate lender $39,800 million, 79.6%. At a 10.5% CET1 requirement the first needs CET1 equal to 4.33% of its assets, the second 8.36%.

Related reading: Financial Regulation by Julian R. Sterling works its subject on one fully specified case, with free companion workbooks. The figures below are an illustrative case built for this article.Get the DRM-free PDF, $19.99 →or see it on Amazon

The formula

RWA density = total risk-weighted assets / total assets

Credit RWA density = credit RWA / total assets, when only credit risk is compared

Capital per dollar of assets = RWA density × capital ratio requirement

The numerator is the bank's reported RWA: credit risk, including off-balance-sheet exposures after their conversion factors, plus market risk and operational risk. The usual denominator is total assets from the balance sheet; some analysts use the leverage exposure measure instead, which adds off-balance-sheet items. Say which one is used, since the two do not give the same percentage. How each exposure's RWA is built line by line is in how to calculate a bank's risk-weighted assets.

The case: two banks of the same size

Illustrative balance sheets in $ million, standardized-style risk weights. Actual weights depend on ratings, loan-to-value and jurisdiction.
ExposureRisk weightBank A assetsBank A RWABank B assetsBank B RWA
Cash and central bank reserves0%4,00003,0000
Government bonds0%6,00004,0000
Loans to banks20%2,0004003,000600
Residential mortgages35%30,00010,5006,0002,100
Retail and SME loans75%4,0003,0008,0006,000
Corporate loans100%3,0003,00024,00024,000
Other assets100%1,0001,0002,0002,000
Credit risk50,00017,90050,00034,700

Bank A lends mainly against homes, Bank B mainly to companies. To the credit RWA each adds operational risk RWA ($2,400 million and $4,200 million) and market risk RWA ($300 million and $900 million), both illustrative.

The calculation

Bank A: credit density = 17,900 / 50,000 = 35.8%; total RWA = 17,900 + 2,400 + 300 = 20,600; density = 41.2%

Bank B: credit density = 34,700 / 50,000 = 69.4%; total RWA = 34,700 + 4,200 + 900 = 39,800; density = 79.6%

Same size, almost twice the regulatory risk. Nothing in Bank A's lower density says it is safer: it says its assets attract lower weights under the rules. Mortgage weights in particular depend on how the rules treat loan-to-value, as shown in mortgage risk weights with loan splitting.

What density does to capital

Multiply density by the capital requirement and the ratio becomes capital per dollar of assets. With an illustrative CET1 requirement of 10.5% (a 4.5% minimum, a 2.5% conservation buffer and 3.5% of Pillar 2 and other buffers):

Bank A: 41.2% × 10.5% = 4.33% of assets, $2,163 million of CET1

Bank B: 79.6% × 10.5% = 8.36% of assets, $4,179 million of CET1

On the same $50,000 million of assets, Bank B needs $2,016 million more CET1. That is why density, and not size, explains most of the difference in equity between lenders with different business models. The ratio itself is set out in how to calculate the CET1 ratio.

When density is low, the leverage ratio binds

The leverage ratio asks for Tier 1 capital as a share of exposure, with no risk weights. It becomes the binding constraint when RWA density falls below the leverage requirement divided by the risk-based Tier 1 requirement.

Switch point = 3% / 12% = 25.0% density (using total assets as the leverage exposure, for simplicity)

Bank A: Tier 1 needed on RWA = 20,600 × 12% = $2,472 million; on leverage = 50,000 × 3% = $1,500 million. The RWA requirement binds.

Bank A's density would have to fall from 41.2% to 25.0% before the leverage ratio took over. A bank with internal models and a large mortgage book can get there, which is the reason the leverage ratio exists; see how to calculate the leverage ratio of a bank.

The free bank stress test template moves RWA and CET1 together quarter by quarter, which is where a change in density shows up first.

Reading density across banks

Takeaway

RWA density = RWA / total assets. Here it is 41.2% for a mortgage lender and 79.6% for a corporate lender of the same size; times a 10.5% CET1 requirement that is 4.33% and 8.36% of assets, and below 25.0% density the leverage ratio takes over.

Questions readers ask

What is the RWA density formula?

Total risk-weighted assets divided by total assets. Bank A has 20,600 of RWA on 50,000 of assets, a density of 41.2%; Bank B has 39,800, 79.6%. Credit RWA alone give 35.8% and 69.4%.

What is a high RWA density?

There is no single threshold; density mostly reflects what a bank lends against and how its weights are calculated. In this case a mortgage-led bank is at 41.2% and a corporate lender at 79.6%, with the same total assets.

Why does RWA density matter for the leverage ratio?

Because the leverage ratio binds when density is below the leverage requirement divided by the Tier 1 requirement: 3% / 12% = 25.0% here. Above that point the risk-based requirement asks for more capital.

Go further

This article applies the method to an illustrative case built for it. Financial Regulation works its own fully specified case chapter by chapter, and every figure it prints is a live formula in the free companion workbooks.

Get the book on Amazon →Free companion files

Also on Amazon UK · Amazon Germany · Amazon France · Amazon Canada

Prefer a PDF? The same book is sold as a DRM-free PDF edition, searchable and printable. Get the PDF edition, $19.99

Not on Amazon: 11 paperbacks by Julian R. Sterling on banking, credit and payments, printed on demand and shipped worldwide. Browse the bookshop →

Also on this site

Reading guide: regulation, compliance and banking → · All 1908 articles →

If this book helped, or didn’t, a few lines on Amazon are worth more than they look: they are what the next reader goes on. Write a review. The workbook stays free either way.